ANALISA PENGGUNAAN SILICON CONTROLLED RECTIFIER PADA ELEKTROPLATING TEMBAGA/BAJA KARBON RENDAH
Abstract views: 536
,
PDF downloads: 330
Abstract
Electroplating is one of the engineering improvements in the characteristics of metal materials. Copper coating is a pre-coating before further coating for steel. The surface area of the material is in line with the strong current requirements required for the normal coating process. However, too much current flowing into the cathode results in erosion at the anode. Silicon Controlled Rectifier (SCR) is a component made of semiconductor silicon. It has a function as a controller or switch. Silicon Controlled Rectifiers can be used to reduce coating currents in copper electroplating. The setting of the coating current can be done on copper electroplating of low carbon steel cathodes with a cross-sectional area of 7500 mm2 of 4.5 A; 5 A; 6 A; 6.5 A and 6.7 A. The best copper coating results with a 10 minute coating time are shown in the current 6.5 A with a coating mass of 1.11 grams and 1.06 grams. This proves the need for a reduction in the maximum flow so that optimal coating is achieved.
References
A. ROZAK, “Analisis Kepadatan Pada Proses Pelapisan Nikel Dengan Variasi Tegangan Dan Lama Pencelupan Baja ST 41,” J. Tek. Mesin, vol. 5, no. 01, 2017.
Basmal, “Pengaruh Rapat Arus Dan Waktu Pelapisan Pada Proses Electroplating Terhadap Ketebalan Lapisan Krom | Politeknosains,” POLITEKNOSAINS J. Ilm. lintas Teknol., vol. 10, no. 2, 2011.
B. Suhendro, T. L. DS, and Suyamto, “Rancang Bangun Dan Analisis Alat Pelapisan Tembaga Menggunakan Teknik Elektroplating,” in SEMINAR NASIONAL SDM TEKNOLOGI NUKLIR VII, 2011.
I. M. Sudana, I. A. A. Arsani, and I. G. . S. Waisnawa, “Alat Simulasi Pelapisan Logam Dengan Metode Elektroplating,” Log. J. Ranc. Bangun dan Teknol., vol. 14, no. 3, p. 190, Mar. 2017.
U. Margono, “Rancang Bangun Transformator 7,2 V/200 A sebagai Catu Daya Filamen Tabung TRIODA ITK 15-2 pada Generator COCKCROFT WALTON MBE LATEKS 300keV/20 mA.” PTAPB-BATAN, Yogyakarta, 2012.
D. Krisnandi, “Aplikasi Kontrol Switch Menggunakan Silicon Controlled Rectifier (SCR) Melalui Parallel Port,” INKOM J. Informatics, Control Syst. Comput., vol. 1, no. 1, pp. 28–34, 2007.
Copyright (c) 2019 Infotekmesin
This work is licensed under a Creative Commons Attribution 4.0 International License.
Authors who publish with this journal agree to the following terms:
- Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.
- Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgement of its initial publication in this journal.
- Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work (See The Effect of Open Access).
