Rancang Bangun Alat Pemanas Induksi Proses Perlakuan Panas
Abstract views: 222
,
PDF downloads: 2148
Abstract
The heat treatment process using the fuel system is very numerous and the heating time is quite long. The use of induction heaters, heat treatment can be done with a shorter time and less energy. The purpose of this research are; (1) Make a plan design, (2) Measure the part of machine element, (3) Measure the estimation of time and design budget, (4) Test the result of induction heater machine. The method in this study uses experimental. The result of concept design evaluation, i.e., the use of trapezoid screw on the lifter system was 0,2 kilowatt of motor power, 12 mm of shaft diameter, and ball bearing 6201 with the age of 0,31 years which determined from the calculation of machine element on the induction heater system. The total of time for making this machine was 3.182,06 minutes and it spent Rp 5.360.700,-. The result of test shows that the hardness rate of raw material mild steel that given heat of hardening temperature of 850 0C, that endured for 45 minutes increasing being 84,3 HRB. However, after being tempered temperature of 400 0C having a decrease being 69 HRB.
References
Y. Zhulkarnaen, n/a Wijono, and M. Dhofir, “Perancangan Dan Pembuatan Pemanas Induksi Dengan Metode Pancake Coil Berbasis Mikrokontroller Atmega 8535,” J. Mhs. TEUB, vol. 2, no. 2, 2014.
R. Ismail, M. Tauviqirrahman, S. S. Sugiyanto, J. J. Jamari, A. Warsito, and A. Syakur, “Pemanfaatan Mesin Pemanas Induksi Untuk Pengerasan Permukaan Roda Gigi Produk UKM,” in Semantik, 2011.
W. P. Raharjo and B. Kusharjanta, “Rancang Bangun Pemanas Induksi Berkapasitas 600 W Untuk Proses Perlakuan Panas Dan Perlakukan Permukaan,” in Prosiding SNST Fakultas Teknik, 2013.
A. YOGANTORO, “YOGANTORO, ANOM. Penelitian Pengaruh Variasi Temperatur Pemanasan Low Tempering, Medium Tempering dan High Tempering pada Medium Carbon Steel Produksi Pengecoran Batur-Klaten terhadap Struktur Mikro, Kekerasan Dan Ketangguhan (Toughness),” Univerversitas Muhammadiyah Surakarta, 2010.
R. L. Mott, Elemen-Elemen Mesin Dalam Perancangan Mekanis. Penerbit ANDI, 2009.
Sularso and K. Suga, Dasar Perencanaan Dan Pemilihan Elemen Mesin. Jakarta: Pradnya Paramita, 1997.
R. S. Khurmi and J. K. Gupta, A textbook of machine design. Eurasia, 2005.
Copyright (c) 2020 Accurate : Journal Of Mechanical Engineering and Science
This work is licensed under a Creative Commons Attribution 4.0 International License.
Authors who publish with this journal agree to the following terms:
- Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.
- Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgement of its initial publication in this journal.
- Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work (See The Effect of Open Access).
