Pengembangan Desain Alat Pemotongan Kripik Singkong Dalam Peningkatan Produksi (Studi Kasus Pada UMKM di Pemalang)
Abstract views: 156
,
pdf downloads: 220
Abstract
Cassava is a tuber plant that can grow in tropical areas with hot and humid climates. In tropical climates
cassava is needed for its growth process so that this plant cannot grow at temperatures below 10 c. Cassava is a
tuber or tree root that can grow on sandy to clay soil, as well as on low fertility soil. The length of cassava
ranges from 15-30 cm with a relatively different diameter, which is 2-5 cm. Cassava has a skin consisting of two
layers, the first layer is the outer skin while the second layer is the inner skin with white or yellowish flesh. In its
production so far, cassava cutting is still using human power (manual). It would be better if the production of
cassava cutting increased without ignoring the existing human aspects. Therefore, a machine is needed as a
human tool in increasing the productivity of cassava cutting. Significant results or not, can later be observed
from the data obtained before and after using the machine. A significant increase after the experiment was
carried out means that the cassava cutting machine was able to help the existing cutting process. This can be
seen later by using SPSS calculations.
References
[2] Y. S. Muhaenah, Sachriani, and Y. Yulianti, “Pelatihan Pembuatan Nugget Singkong Pada Masyarakat Wilayah Kelurahan Benda Baru, Pamulang, Tangerang Selatan,” J. ABDITEK (Jurnal Pengabdi. Kpd. Masy. Fak. Tek., vol. 1, no. 1, pp. 32–45, 2021.
[3] N. ANNET, “SUBSTITUSI TEPUNG KULIT SINGKONG (Manihot utillisima) DALAM PEMBUATAN MIE DENGAN PENAMBAHAN EKSTRAK KELOPAK BUNGA ROSELLLA KERING (Hibiscus sabdariffa Linn.) SEBAGAI PEWARNA ALAMI Oleh:,” 2014.
[4] I. A. K. Suriadi, I. D. G. A. Subagia, and I. K. A. Atmika, “Penerapan Mesin Pengiris Singkong Pada Industri,” J. Udayana Mengabdi, vol. 15, no. 2, pp. 118–124, 2016.
[5] S. & Mehmood, “ALAT TEPAT GUNA,” vol. 16, no. 22, pp. 119–128, 2011.
[6] A. Mayssara A. Abo Hassanin Supervised, “Motor Listrik,” Pap. Knowl. . Towar. a Media Hist. Doc., pp. 6–46, 2014.
[7] T. Sutrisno, “Desain Geometri Open Pulley System 4 Tingkat Pada Unit Mesin Penggerak Turbin Uap Dan Generator Untuk Steam Power Generation (Longitudinal Coil Water Tube Boiler),” pp. 9–66, 2002.
Copyright (c) 2021 Accurate: Journal of Mechanical Engineering and Science
This work is licensed under a Creative Commons Attribution 4.0 International License.
Authors who publish with this journal agree to the following terms:
- Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.
- Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgement of its initial publication in this journal.
- Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work (See The Effect of Open Access).
