Analisa Pengukuran Ketebalan Steel Block, Aluminium Block dan Steel Plate Menggunakan Ultrasonic Thickness Gauge
Abstract views: 0
,
Abstract
Thickness measurement using an ultrasonic sensor is a type of non-destructive test (NDT) that is commonly used in various industries. Measurement of thickness (thickness) on steel blocks, aluminum blocks and steel plates using an ultrasonic thickness gauge. The method used is the contact testing method which is then compared with manual measurements. Based on data analysis from the measurement results, it was found that the thickness with the highest percent error was in the Steel S3 sample, namely 93.87%. Meanwhile, the thickness measurement with the lowest percent error in the Steel plate sample was 0%. Meanwhile, for measuring the dimensions of artificial corrosion defects, the smallest error percentage obtained was 0% for several dimensions, with the average measurement error obtained being 22.82%. The profile shape of the detected artificial corrosion defects is exactly the same as the reference profile. So, measuring the thickness of steel blocks, aluminum blocks and steel plates as well as measuring artificial corrosion defects located in steel plates can be detected well and the measuring results can be trusted.
References
[2] D. A. Kiefer, M. Fink, and S. J. Rupitsch, “Simultaneous Ultrasonic Measurement of Thickness and Speed of Sound in Elastic Plates Using Coded Excitation Signals,” IEEE Trans. Ultrason. Ferroelectr. Freq. Control, vol. 64, no. 11, pp. 1744–1757, 2017, doi: 10.1109/TUFFC.2017.2746900.
[3] A. Ashraf, “Ultrasound Communication through Thin Plates : Understanding the Channel Ultrasound Communication through Thin Plates : Understanding the Channel”.
[4] K. Nakamura, “Evaluation Methods for Materials for Power Ultrasonic Applications,” Jpn. J. Appl. Phys., vol. 22, no. 1, pp. 16–20, 2020, doi: 10.35848/1347-4065/ab9230.
[5] M. I. R. Jaya, A. Fahruddin, and A. Akbar, “Pengukuran Thickness Menggunakan Probe Normal Ultrasonic Testing Non-Destructive Dengan Metode Contact Testing Variasi Kuplan Oli 10w, 15w, Dan 20w Pada Material Baja,” UMSIDA, 2024, doi: 10.21070/ups.3842.
[6] N. A. Aziz, “Pengukuran Ketebalan pada Material Baja dengan Ultrasonic Testing Menggunakan Metode Contact Testing dengan Variasi Media Koplan Oli, Air, dan Gel,” Institut Teknologi Sepuluh Nopember, 2018.
[7] D. Zuljan, “Effect of ultrasonic coupling media and surface roughness on contact transfer loss Effect of ultrasonic coupling media and surface roughness on contact transfer loss,” Cogent Eng., vol. 9, no. 1, 2022, doi: 10.1080/23311916.2021.2009092.
[8] N. Netshidavhini and R. B. Mabuza, “Effects of Various Couplants on Carbon Steel and Aluminium Materials Using Ultrasonic Testing,” in 18th World Conference on Nondestructive Testing, 2012, no. April, pp. 16–20.
[9] Sutrimo and M. Luthfi, “Analisis Cacat Buatan pada Sambungan Pelat dan Sambungan Pipa Baja dengan Las GMAW Menggunakan Ultarasonic Test,” TEDC, vol. 8, no. 1, pp. 14–19, 2014.
[10] M. A. Syarifuddin and A. Akbar, “Analisa Cacat Las Pipa Pembakaran Boiler dengan Metode PAUT ( Phased Array Ultrasonic Testing ),” no. 1, pp. 1–7, 2024.
[11] F. Han, L. Zhang, and K. Cui, “Measuring thickness of object with ultrasonic thickness gauge,” MATEC Web Conf., vol. 175, pp. 4–8, 2018, doi: 10.1051/matecconf/201817503029.
[12] BSEN, Spesification for Calibration Block No . 2 for Ultrasonic Examination of Welds, no. 2. British Standar Institution, 1992.
[13] F. Debora, “Pengukuran Ketebalan serta Posisi Cacat pada Sampel Carbon Steel dan Stainless Steel dengan Metode Ultrasonic Testing,” Jur. Fis. FMIPA, p. 6, 2015.
[14] I. Pan American Industries, “UltrasoundVelocity,” USA, 2024.
[15] A. A. Supriyanto and Syafrizal, “Penentuan Cacat dengan Metode Ultrasonic Testing,” J. RAMATEKNO, vol. 2, no. 1, pp. 7–13, 2022.
[16] G. T. and E. Services, Course Introduction and Objectives Ultrasonic Testing. TWI Ltd, 2021.
Copyright (c) 2025 Ulikaryani Ulikaryani, Unggul Satria Jati, Radhi Ariawan, Dian Prabowo, Sabtun Ismi Khasanah, Hamid Abdillah
This work is licensed under a Creative Commons Attribution 4.0 International License.
Authors who publish with this journal agree to the following terms:
- Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.
- Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgement of its initial publication in this journal.
- Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work (See The Effect of Open Access).
